acdc specification 200 watts ? worldwide medical approvals ? single, dual, triple and quad outputs ? power fail detect ? remote on/off ? uchannel and enclosed versions ? 100 watt convectioncooled rating ? 3 year warranty pbm200 series input input voltage ? 90-264 vac input frequency ? 47-63 hz input current ? 3.2 a rms at 115 vac, 1.6 a rms at 230 vac inrush current ? 20 a at 115 vac, 40 a at 230 vac cold start 25 c power factor ? 0.98 typical earth leakage current ? 90 a max at 115 vac/60 hz 150 a max at 230 vac/50 hz input protection ? internal t4 a/250 v in line and neutral output output voltage ? see table output voltage trim ? not user-adjustable initial set accuracy ? 2% minimum load ? see table & note 5 start up delay ? 2 s max start up rise time ? 18 ms typical hold up time ? 20 ms minimum at full load & 110 vac drift ? 0.2% line regulation ? 0.5% max load regulation ? see note 7 transient response ? 4% max deviation, recovery to within 1% in 500 s for a 25% load change ripple & noise ? 2% max pk-pk, 20 mhz bandwidth with a 22 f electrolytic & a 0.47 f tantalum capacitor overvoltage protection ? 112-140% vnom output 1 only, recycle input to reset overtemperature ? shutdown at +85 c (singles) or +105 c protection (multi outputs) with auto recovery, measured internally overload protection ? 110-150% typical, auto recovery short circuit protection ? trip and restart (hiccup mode) temperature ? 0.04%/c coefficient remote sense ? single output models only. compensates for up to 0.5 v drop remote on/off ? on = logic low or open circuit off = logic high xppower.com general efficiency ? 80% maximum isolation ? 4000 vac input to output 1500 vac input to ground 500 vac output to ground switching frequency ? 100 khz 12 khz signals ? power fail detect, remote on/off power density ? 4.76 w/in 3 power fail detect ? ac ok = ttl logic high ac not ok = ttl logic low mtbf ? 350 khrs to mil-hdbk-217f at +25 c, gb environmental operating temperature ? 0 c to +70 c, derate linearly from 100% power at +50 c to 50% power at +70 c cooling ? c versions have internal fan, b versions are derated with convection cooling or require 25 cfm (see note 4) operating humidity ? up to 95% rh, non-condensing storage temperature ? -40 c to +85 c operating altitude ? 2500 m shock ? half sine pulse. acceleration 50 g, 11 ms duration, 3 shocks in each direction, unpackaged, non-operating vibration ? sinusoidal 10-55 hz, amplitude 0.15 mm, 30 min/axis, unpackaged, non-operating emc & safety emissions ? en55011 & fcc class b conducted & radiated harmonic currents ? en61000-3-2, class a voltage flicker ? en61000-3-3 esd immunity ? en61000-4-2, level 3 perf criteria a radiated immunity ? en61000-4-3, level 3 perf criteria a eft/burst ? en61000-4-4, level 3 perf criteria a surge ? en61000-4-5, level 3 perf criteria a conducted immunity ? en61000-4-6 3 v, perf criteria a dips & interruptions ? en61000-4-11, 30% 10 ms, 60% 100 ms, >95% 5000 ms, perf criteria a, b, b safety approvals ? en60601-1, ul60601-1, csa22.2 no. 601-1 per cul
06-may-09 acdc pbm200 models and ratings notes 1. for u-bracket format, replace suffix -c with suffix -b. 2. output 2 peak current is 12 a on +12 v, 9 a on +15 v, and 6 a on +24 v. maximum 2 s duration with total load <200 w. 3. output 4 is floating and can be connected externally for positive or negative output. 4. 200 w for -c version with a cover and fan assembly. 100 w for -b version with convection cooling (maximum current of output 1 & 2 derated to 50%). 200 w for -b version with 25 cfm forced air provided by user. 5. zero minimum load for outputs 2, 3 & 4. 10% minimum load required on output 1 for all outputs to meet regulation. 6. when the remote sense facility is not used, +sense must be connected to +v, and Csense to return, on p2 connector. 7. total regulation includes initial tolerance, line regulation and load regulation. 8. peak current for single output models is 110% of imax. maximum 2 s duration with 10% duty cycle. mechanical details 7.00 (177.8) 1.00 (25.4) 3.00 (76.2) 0.50 (12.7) 6.00 (152.4) 0.50 (12.7) 0.85 (21.6) a l n g p2 p1 p4 1 1 p3 a a a a a a a 4.00 (101.6) 1.50 (38.1) 1.00 (25.4) 1 9 a: mounting holes. threaded inserts for m3 0.5 screws (8 places) p5 b b b: mounting holes. threaded inserts for 6.32" screws (8 places) b b b b b b 0.65 (16.5) 2.30 (58.4) 1 notes gc h7;3cb 1=<<31b=@ vg 7a h7<9:3 h)bmobfeg,bema =cb>cb 1=<<31b=@ vi 7a h7<9:3 h)bmobfeg,bew a1@3ea /@3 sma t7193: >:/b32c nc g=<<31b=@ vm ;/b3a e7b6 s=:3f 6=ca7<5 iibegbgenm & s=:3f nenno a3@73a 1@7;> b3@;7 b3@;77< i l/=a7b7d3a >7< i 7a @3bc@>@=fc 4=@ ibfj d3@a7=>@=fc 4=@ ibgj d3@a7= |
